SERVICE PRICE LIST:

-Apply Linseed Finish to Wood ($25)

-Black Oxide/Bluing Service Thorough H&M Metal Processing: ($250)

-Build Service Complete Parts Kit: Standard ($625)

-Build Service Complete Parts Kit: Folder ($650)

-Build Service Complete Parts Kit: Milled Receiver Press-in Barrel: Standard ($625)

-Build Service Complete Parts Kit: Milled Receiver Threaded Barrel: Standard ($625)

-Build Service: Populated Barrel ($399)

-Build Service: Populated Barrel Milled Receiver Press In ($375)

-Build Service: Populated Barrel Milled Receiver Threaded ($425)

-Build Service: Populated Barrel Folder ($425)

-Conversion: Fixed Stock Saiga ($575)

-Conversion: Fixed Stock Saiga to 4.5mm/5.5mm Side Folder ($725)

-Conversion: Build Galil in 7.62x39mm ($825)

-Cerakote Service: 1-Color, Metal Only ($300)

-Cut/Crown Populated Barrel ($250)

-Cut/Crown/Drill Limiter on Arsenal ($275)

-Cut/Crown/Thread Populate Barrel ($325)

-Cut/Crown/Thread/Pin & Weld Muzzle Device Populate Barrel ($350)

-Demil AK/Install New Receiver ($399)

-Demil AK/Parts Kit ($99)

-Drill Limiter on Arsenal AK ($150)

-Drill/Install New Barrel Pin ($75)

-Drill/Pin Gas Piston ($60)

-Finish 80% Receiver: Welded & Heat Treated ($75)

-Folding Stock Conversion ($199)

-Install 4.5mm/5.5mm Side Folder ($275)

-Install AK Optics Side Rail ($60)

-Install Sling Loop: Rear AK Receiver ($35)

-Install/Adjust/Tune Trigger: Tapco G2 OR Similar (Trigger not included) ($70)

-Laser Engraving: (Minimum Charge $45.  Call for Estimate)

-Manufacture/Heat Treat Pin ($5)

-Nitride Service (QPQ) ($250 per firearm: Black Oxide Will Be applied to Trunnions, Receivers, Bolts and Springs Due to Heat Treat Concerns.  Additional charge for already complete firearms due to need to disassemble for separate treatment.)

-Polish AK Internals ($60)

-Polish and Tune AK Receiver Rails ($60)

-Pre-Ban to Post-Ban Back End Conversion ($250)

-Press and Pin Front Sight Assembly or Gas Block ($99)

-Remove Barrel/Install New Barrel ($325)

-Remove Rusted Muzzle Brake ($99)

-Replace Milled Receiver ($325)

-Replace Stamped Receiver on AK ($425)

-Rifle Inspection ($25)

-Single Barrel Block Straightening ($99)

-Straighten/Re-pin Gas Block, FSB and RSB ($275)

-Turn AK Barrel Journal: During Conversion/Install ($150 + $20/Journal)

-Transfer Firearms Charge ($30)

-Weld and Finish Receiver Holes ($125)

 

NFA Gunsmithing

-NFA Firearms Marking ($45)

-Build SBR: ATF Form 4 (Call for Pricing)

-Build Post Sample Machinegun: Class 07 FFL/02 SOT Required (Call for Pricing)

PURCHASING A RIFLE AND GUNSMITHING SERVICE

CONTACT ME:  I do not have an automated system.  If you wish to purchase a rifle directly from me that is listed on my web site, or one that is listed on Armslist.com, please give me a call at (406) 792-5851 or send an email to fowlerarms@protonmail,com.  Title the email as PURCHASE REQUEST or SERVICE REQUEST.  Please be sure to leave a message if you call.  My shop is noisy, and I don't have any employees, so it is likely that I won't pick up.  I typically do not return calls if there is not a message left.

SALES FORMATSI may list items on multiple formats simultaneously, such as Gunbroker.com, Armslist.com and on my web page.  Purchases through Gunbroker.com can be made through the normal Gunbroker.com purchasing process.  Contact me for items found on other formats.  Gunsmithing service is listed below.

PAYMENT:  I no longer accept credit cards.  I can accept USPS money orders and personal checks,   I can also accept Zelle and Venmo payments in some circumstances.  All checks must clear the bank before the rifle will be shipped.  PLEASE CONTACT ME PRIOR TO SENDING ANY FORM OF PAYMENT.  I may have items listed on multiple formats and must ensure that a sale has not already been made.

SHIPPING: Firearms will only be shipped to a legal and current Federal Firearms Licensee.  After paying for a firearm, please let me know what licensee near you that you would like the rifle shipped to.  I will contact them and obtain a copy of their Federal Firearms License (FFL).  I will verify the FFL, contact the license, package the firearms and ship it to the licensee.  I will ship UPS ground with $900 insurance.  Additional insurance can be provided at your request.  Shipping will typically be $50 but may vary depending on the size of the item and where it is being shipped to.  If you provide me your email address, I will have UPS send you shipment updates.  I will then ship the firearm to the FFL license that you request that it be shipped to.  When the firearm arrives, you will simply complete the same purchasing process as if you were buying the firearm from them.  The only difference is that you will have already paid me for the firearm.  The FFL licensee receiving the firearm will transfer it to you and may require a small processing fee.

Please be sure that it is legal for YOU to possess the firearm in the jurisdiction that it is to be transferred to you in and that the service requested is legal.  You will be charged for shipping the firearm back to me in addition to a $50 processing fee if you are unable to complete the transfer due to it not being legal in your jurisdiction or it being illegal for you to possess.  The original purchase price minus shipping and handling will be refunded to you after I receive the firearm back from the licensee that was unable to transfer it to you. 

Please feel free to contact me if you have any questions or concerns.  Be sure to leave a message as I will likely not hear the phone and pick up right away.  I don't typically return calls to unknown numbers unless they leave a message.

922R COMPLIANCE:

Section 922r of US Code, Title 18 is a regulation which pertains to building or modifying a semiautomatic rifle or shotgun from imported parts. This law impacts importers, manufacturers, gunsmiths and consumers who assemble their own firearms.

Sec. 178.39 Assembly of semiautomatic rifles or shotguns

No person shall assemble a semiautomatic rifle or any shotgun using more than 10 of the imported parts listed in paragraph (c) of this section if the assembled firearm is prohibited from importation under section 925(d)(3) as not being particularly suitable for or readily adaptable to sporting purposes.

The provisions of this section shall not apply to:(1) The assembly of such rifle or shotgun for sale or distribution by a licensed manufacturer to the United States or any department or agency thereof or to any State or any department, agency, or political subdivision thereof; or(2) The assembly of such rifle or shotgun for the purposes of testing or experimentation authorized by the Director under the provisions of Sec. 178.151; or(3) The repair of any rifle or shotgun which had been imported into or assembled in the United States prior to November 30, 1990, or the replacement of any part of such firearm.

For purposes of this section, the term imported parts are:

(1) Frames, receivers, receiver castings, forgings or stampings

(2) Barrels

(3) Barrel extensions

(4) Mounting blocks (trunions)

(5) Muzzle attachments

(6) Bolts

(7) Bolt carriers

(8) Operating rods

(9) Gas pistons

(10) Trigger housings

(11) Triggers

(12) Hammers

(13) Sears

(14) Disconnectors

(15) Butt stocks

(16) Pistol grips

(17) Forearms, hand guards

(18) Magazine bodies

(19) Followers

(20) Floor plates

IN SUMMARY:  ALL STANDARD AK RIFLES MUST HAVE (6) USA MADE PARTS FROM THE LIST ABOVE TO BE IN COMPLIANCE.  THIS CODE DOES NOT APPLY TO AK PISTOLS.

NFA FIREARMS:

I can only build Post Sample Machineguns for persons who posses a Class 07 FFL/02 SOT.  I can build short barreled rifles and convert non-NFA firearms with an ATF Form 4.  I can conduct gunsmithing on NFA firearms with a copy of your ATF Form 1.

Thanks for your business!

 

//www.fowlerarms.com/wp-content/uploads/2019/04/surprises.png

All costs related to the service provided will be determined prior to any work being started. There will be absolutely no surprise bills or price hikes upon completion! All unsuspected costs discovered during the build process will be uncured by me. It is my responsibility to determine what will be required prior to taking on a job.

 

P.O. Box 393 Wilsall, MT 59086     fowlerarms@protonmail.com    (406) 792-5851